مصالح و سازه های بتنی

مصالح و سازه های بتنی

اثر دانه‌بندی ماسه بر خواص ملات‌های استاندارد مورد استفاده در کنترل کیفیت سیمان

نوع مقاله : مقاله پژوهشی

نویسندگان
1 کارشناسی ارشد مهندسی زلزله، گروه مهندسی عمران، دانشگاه صنعتی شریف، تهران، ایران.
2 دانشیار دانشکده مهندسی عمران، دانشگاه صنعتی خواجه نصیرالدین طوسی، تهران، ایران.
3 کارشناسی ارشد مهندسی مدیریت ساخت، شرکت فهاب بتن، تهران، ایران.
4 عضو هیئت مدیره شرکت فهاب بتن
چکیده
کنترل کیفی مقاومت سیمان به ویژگی‌های ملات استاندارد، به‌ویژه دانه‌بندی ماسه و نسبت اجزای مخلوط، وابسته است. هدف این پژوهش، بررسی تأثیر دانه‌بندی ماسه بر خواص تازه و سخت‌شده ملات استاندارد و ارزیابی قابلیت استفاده از ماسه سیلیسی از منبع داخلی در آزمون‌های کنترل کیفی سیمان بود. بدین منظور، ماسه سیلیسی از منبع داخل کشور با دانه‌بندی مطابق ASTM C778 و EN 196-1 و ماسه استاندارد وارداتی از آلمان مطابق EN 196-1، با نسبت‌های اجزای ASTM C109 و EN 196-1، در تهیه ملات استاندارد به‌کار گرفته شدند. نتایج نشان داد تخلخل بین‌دانه‌ای ماسه با دانه‌بندی ASTM در حالت شل 36.48 درصد، در مقایسه با 28.87 درصد برای ماسه با دانه‌بندی EN، بیشتر است. در نتیجه، ملات حاوی ماسه ASTM خمیر کافی برای پرکردن فضای خالی بین دانه‌ها نداشته که موجب افت بیش از 50 درصدی مقاومت فشاری 28 روزه شد و در آزمایش میز جریان نیز به‌صورت خشک و غیرمنسجم پخش گردید. مقاومت فشاری ملات استاندارد ساخته شده با ماسه داخلی با دانه‌بندی EN، مشابه نتایج حاصل از ملات ساخته شده با ماسه استاندارد وارداتی EN بود و به‌نظر می‌رسد گزینه مناسبی در مقایسه با ماسه‌های وارداتی در آزمون‌های کنترل کیفی سیمان در ایران باشد.
کلیدواژه‌ها

عنوان مقاله English

Effect of Sand Gradation on the Properties of Standard Mortars Used for Quality Control of Cement

نویسندگان English

Farhad Daemi Kabiri 1
Alireza Bagheri 2
Erfan Radmonfared 3
Babak Froutanmehr 4
1 Farhad Daemi Kabiri, M.Sc. in Earthquake engineering, Department of Civil engineering, Sharif University of Technology, Tehran, Iran.
2 Associate Professor, Faculty of Civil engineering, K. N. Toosi University of Technology, Tehran, Iran.
3 M.Sc. in Construction engineering and Management, Fahab Beton Company, Tehran, Iran
4 Member of the Board of Directors, Fahab Beton Company, Tehran, Iran
چکیده English

Quality control of cement strength is dependent on the characteristics of the standard mortar, particularly sand gradation and mixture proportions. This study aimed to investigate the effect of sand gradation on the fresh and hardened properties of standard mortar and to evaluate the suitability of locally produced silica sand for cement quality control tests. For this purpose, silica sands conforming to the gradation requirements of ASTM C778 and EN 196-1, along with imported standard sand from Germany conforming to EN 196-1, were used to prepare standard mortars based on the mixture proportions specified in ASTM C109 and EN 196-1. The results showed that the interparticle void content of the ASTM C778 sand in the loose state was 36.48%, compared with 28.87% for the EN 196-1 sand. Consequently, the mortar containing ASTM sand lacked sufficient paste to fill the voids between the sand particles, resulting in a reduction of more than 50% in the 28-day compressive strength. Moreover, the mortar exhibited a dry and non-cohesive spread in the flow table test. In contrast, although the workability of the mortar containing locally produced sand conforming to EN 196-1 was slightly lower, its 28-day compressive strength was comparable to that of the imported sand, ranging from 39.6 to 41.2 MPa, compared with 39.5 MPa for the imported sand. Therefore, locally produced silica sand conforming to EN 196-1 can be considered a suitable alternative to imported standard sand for cement quality control testing in Iran.

کلیدواژه‌ها English

cement quality control
compressive strength
standard mortar
standard sand

  • تاریخ دریافت 24 شهریور 1405
  • تاریخ بازنگری 16 آبان 1405
  • تاریخ پذیرش 01 آذر 1405